Table of Contents

EyeLink Task Computer Setup

This page outlines steps needed to setup SR Research EyeLink 1000 Plus for in-scanner eye tracking. The SR Research participant setup video 1) covers this in more detail.

Before your first time setting up, be sure to complete the mandatory Qualtrics MRRC EyeLink Quiz. For live participant sessions, we have a checklist document on sharepoint

Once the camera and task PC are setup, you likely want to run SR Research EyeLink Calibration.

Other eye tracking topics include EyeLink Task Integration, EyeLink Analysis, and SR Research EyeLink Install.

Setup Steps

Prisma 1 and Prisma 2 have slightly different EyeLink configurations. In either, the two major steps are the same. You want to

  1. connect the EyeLink Host PC to the Task computer (EPrime PC or Laptop) using the provided Ethernet cable and
  2. present the camera view to the projector for the technologist using control64.exe 2).

The Ethernet connection must be attached before starting and removed after finishing each scan that will use eye tracking. 3). We'll also need to pull out and put back the EyeLink Mouse and Keyboard every time they are used. 4)

Prisma 1

  1. Display your laptop or the MRRC Win11 computer to the projector.
  2. Turn on the EyeLink “Host PC” tower under the desk
  3. Attach the Ethernet cable to the bottom yellow labeled “eyelink” port on the back of the Eyelink Host PC.
  4. Use EPrime PC/Laptop to connect to EyeLink with control64.exe

    • Blue eye icon on desktop OR C:\Program Files (x86)\SR Research\EyeLink\SampleExample\ (from SDK)

    • If EPrime PC says “Connection failed” or EyeLink PC says “CABLE FAULT”, check Ethernet cable from earlier is fully plugged in and in the bottom port.

    • You should see a blank gray screen on the EPrime PC and Link Open on EyeLink

  5. Pull out the EyeLink keyboard and mouse
  6. Display the full eye image on the projector (cloned EPrime PC display) to help the technologist setup.
    • Push Enter to stream the EyeLink camera on the EPrime computer
    • Push ➡ (right arrow key) to show the full image

      The EyeLink display will contiue to show both views

  7. Adjust and Calibrate
  8. Exit control64.exe
    1. tap Escape
    2. hold Control and tap c (ie. push Ctrl+c)
      • Ctrl+c only works from the EPrime PC keyboard. Use Camera Setup & toggle Image→display from the EyeLink interface

Prisma 2

  1. Use the EPrime PC
    • switch the eye tracking kvm box to 1 5)
  2. Ensure the EyeLink host PC (farthest left tower on lowest shelf) is on
  3. Plug the “EyeLink” blue sticky labeled Ethernet cord into the bottom “EyeLink” labeled port.
    • you may need to move the green tape to uncover the port
  4. click the blue eye icon “calibration” (control.exe) on the desktop to run the eye video presenting software
  5. show video once launched and gray screen is presented
    1. push enter on the keyboard to display the eye video
    2. push right arrow to see the full (un-zoomed) video collected by the tracker
  6. confirm eye is in focus and good thresholds can be set (see SR Research EyeLink Calibration)
  7. exit the video screen
    1. push the Escape key
    2. hold control and tap c, release all keys
1)
and to a lesser extent the Siemens Tray Mount and Eye Tracker Positioning (illuminator) video
2)
desktop icon links to C:\Program Files (x86)\SR Research\EyeLink\SampleExperiments\ from the EyeLink SDK
3)
A connected Ethernet cable can be problematical for eprime
4)
Multiple keyboards will be very confusing for other users.
5)
may be on display #2, showing screen for Avotech/Arrington eye tracking